Product Description

Rubber Lined Carbon Steel Pipe

Rubber Lined Steel Pipe protect Pipeline with their Characteristic of wear resistance, corrosion resistance, high temperature resistance.

Rubber Lined Steel Framework:

♠ Pipe Framework of Rubber Lined Steel Pipe Is Carbon Steel Pipe Or Stainless Steel Pipe

♠ Rubber Lining is High Wear Resistant Rubber, Corrosion Resistant Rubber, High Temperature Resistant Rubber

♠ With Adhesives made by our workshop.

♠ So that make sure Rubber Lined Steel Pipe will be well use.

Rubber Lined Steel Spool Work Application Area:

♥ Rubber Lined Steel Fitting For Mine Tailings Mining Slurry Pipeline

♥ Rubber Lined Steel Pipe For Sea Water Dredging pipeline

♥ Rubber Lined Steel Spool Work Electric-power plant desulfurization Pipeline

♥ Rubber Lining Steel Pipe Chemical plant factory sewage pipeline

Carbon Steel Pipe Rubber Liner Materials:

Natural Rubber，Poly Urethane Rubber，Butyl Rubber，Nitrile Butadiene Rubber，Chloroprene Rubber，Hypalon Rubber，Ethylene Propylene Rubber，Styrene Butadiene Copolyme Rubber，Synthetic Rubber，Abrasive Rubber，Anti Corrosive Rubber，Acid Resistant Rubber，Alkali Resistant Rubber，Salt Resistant Rubber，High Temperature Resistant Rubber，Oil Resistant Rubber，Vulcanized Rubber，Pre Vulcanized Rubber

Rubber Lined Steel Piping Method：

There are two Method of rubber lining Steel piping: heat vulcanizing bonding method and cold vulcanizing bonding method.

1> Heat vulcanization bonding

Through vulcanization Tank, under high temperature and high pressure, Making the rubber vulcanization bonding on Carbon Steel Inner Surface.

One objective is to allow the rubber lining to be vulcanized by external conditions,

Another objective is to bond the rubber liner to the inner surface of the Rubber Lined Steel Spool Work by means of a heat vulcanizing.

2> Cold vulcanization bonding method

Through the special vulcanizing adhesive,

Making rubber lining direct bonding,

After bonding, Then the Rubber lined Steel Framework can be used directly

Rubber Lined Steel Pipe And Fitting Feature:

♣ High wear resistance: Impact resistance

♣ High strength: Good Anti-abrasion, Effectively avoid damage caused by water hammer

♠ High corrosion resistance: Fine Anti-corrosion

♣ Acid resistance, alkali resistance, corrosion resistance

♣ Prevent chemical damage to steel Pipe Skeleton Frame

♣ Slowing down fouling

♣ Adhesion of Rubber Lined Steel Pipe is very strong

♣ Less running resistance can reduce energy consumption;: Transmission medium resistance is very small

♣ Can be transported by a wide variety of fluid media

♣ Working Service life can be up to 15~50 years

♣ Energy saving, environmental protection, high efficiency

♣ High temperature resistance: Adapting to wide range of temperature: Working temperature: -50℃～+150℃

♣ Main transport medium:wear and corrosive medium Slurry medium

♣ Can reduces the impact abrasion of the conveying medium on the steel Pipe Skeleton Frame wall

♠ Light weight, easy to install, maintain and transport;

♠ Recycling and reusing.

Rubber Lined Elbow Pipe 

Linings are a premium form of corrosion protection for some of the most severe chemical and abrasive environments. Natural and butyl rubber linings withstand a variety of high-concentration acids and are the optimum choice for high heat and abrasive environments. Additionally, the elasticity of a rubber lining easily accommodates thermal expansion and contraction as well as vibration. 

Rubber lined steel tube main features are as the follows: 
1. The chemical properties are stable, and the characteristics of high heat-resistance and anticorrosion are also excellent; 
2. The impact resistance is strong due to the outer protective layer of steel; 
3. Pipes is connected with flange, and easy to installation 

The Company's product solutions enable its customers to address the challenges presented by demanding industrial applications, including: 

Mining, transporting and processing abrasive particles of varying sizes, 
Transporting and processing corrosive materials with varying chemical properties, 
Transporting slurry via pipeline at extreme temperature differences (interior vs. Exterior), 
Managing equipment wear performance in light of high velocity transportation, 
Reducing work injury from the installation and maintenance of equipment, 
Maximizing the speed and effectiveness of all mining, transporting and processing functions, 
Minimizing the impact and wear/tear on equipment placed in harsh environments, 
Minimizing the replacement or servicing of wearable equipment and 
Minimizing the use of costly and hard-to-find skilled labor 
Delivery time: 
Within 30 days after receipt of the deposit 

Packaging trem: 
Unfumigation wooden case (Out package) and Plastic film and Textile membrane(inside package). We can make change as your request. 

 

The main dimension of pipe fittings
specification	D.D.*wall thickness	1.5D standard elbow			3D tee	Reducing fittings	Straight pipe
		R	90°	45°	Center size
25A	Ф32*3	38	90	90	115	-	500
32A	Ф38*3	48	100	100	125	130	1000
40A	Ф45*3	57	110	110	130	140	2000
50A	Ф57*3.5	76	130	130	140	150	3000
65A	Ф76*4	95	150	150	155	170	3000
80A	Ф89*4	114	130	130	165	170	5000
100A	Ф108*4.5	152	160	160	180	180	6000
125A	Ф133*4.5	190	200	200	200	210	6000
150A	Ф159*5	229	235	235	220	230	600
200A	Ф219*6	305	315	315	260	240	6000
250A	Ф273*7	381	390	390	300	260	6000
300A	Ф325*8	457	470	470	340	310	6000
350A	Ф377*9	533	545	545	365	490	6000
400A	Ф426*9	610	620	620	400	510	6000
450A	Ф480*10	685	700	700	430	540	6000
500A	Ф530*10	500	500	500	470	660	6000
600	Ф630*8	650	650		600	800	6000
700	Ф720*8	750	750		700	800	9000
800	Ф820*8	850	850		800	800	9000
900	Ф920*8	950	950		900	900	9000
1000	Ф1020*10	1050	1050		1000	900	9000
1100	Ф1120*10	1150	1150		1100	900	9000
1200	Ф1220*10	1250	1250		1200	900	9000

STEEL PIPE
O.D	O.D tolerance	W.T	Thickness Tolerance
141.3—273mm	±0.03	3.96—11.13mm	±0.02
Length	6—12m, according to the customers’ requirements
International Standard	ISO9001   ISO14001
Material	A45
Technique	Welded
Packing	In bundles or according to customers’ request
Usage	For low pressure liquid delivery such as water, gas and oil For construction, e.g. building greenhouse
Main market	Middle east, Africa, North and South America, East and West Europe, South and southeast Asia, Australia
Place of Origin	China
code	450000
Productivity	3000ton/month
Processing technology available	Threading, coupling

  Material Used for Rubber Lining of Piping System
Rubber linings are mainly used for protection against corrosion and/or erosion damage.

A wide range of rubbers and elastomers are available for lining vessels, tanks and piping.
Rubbers can also be made with anti-static properties to give a low surface electrical resistance.
Hard rubbers, i.e. hardness greater than Shore D 60, can only be applied by autoclave vulcanization, and therefore hard rubber lining is restricted to small equipment or components. Only soft rubbers can be applied on site.
Hard rubber linings can only be applied to rigid structures and they are also sensitive to large temperature fluctuations. Soft rubber linings remain elastic over a large temperature range, and consequently they can accommodate major deformation, vibrations and significant temperature changes.
With respect to safety aspects, pressure rating, etc. the regulations which apply to piping, equipment and structures are also valid for rubber-lined systems.
Material Selection
Material selection is determined by:
- service conditions (pressure, temperature, medium, etc.)
- design
- manufacturing method
The following rubber types are used for lining purposes (classification according to ASTM D 1418):
- Isoprene or natural rubber (NR)
- Synthetic isoprene rubber (IR)
- Styrene-butadiene rubber (SBR)
- Chloroprene rubber (CR)
- Butyl rubber (IIR)
- Broom-butyl rubber (BIIR)
- Chloro-butyl rubber (CIIR)
- Nitrile-butadiene rubber (NBR)
- Ethylene propylene rubber (EP, EPDM)
- Urethane rubber (UR)
- Chlorosulphonated polyethylene (CSM)**
- Fluoro elastomer (FKM)*
* Commercially available under trade name "Viton" (DuPont product)
** Commercially available under trade name "Hypalon" (DuPont product)
Depending on the degree of vulcanization, rubbers can be classified as 'soft' rubber or as 'hard' rubber. The hardness of soft rubbers is expressed in Shore A, and the hardness of hard rubbers is expressed in Shore D (ASTM D 2240).

Hard rubbers (or Ebonites), i.e. with a hardness higher than Shore D 60, can be produced from NR or blends, e.g. NR/IR, NR/SBR and NR/IR/SBR.
Properties of Rubber
Each rubber material has a specific limit in terms of allowable service temperature and chemical resistance. The chemical resistance and temperature limits for continuous service of several rubber types are given below.
1. Natural rubber (NR)
Soft and hard natural rubber linings are suitable for handling most inorganic chemicals, with the exception of strong oxidising agents such as chromic and nitric acids. Natural rubber linings are also suitable for handling hydrochloric acid. Natural rubber is also resistant to most organic fluids, including alcohols and most esters. They should not be used in the presence of aliphatic or aromatic hydrocarbons, halogenated hydrocarbons, mineral oils and certain vegetable oils. The allowable service temperature range is -40 °C to +80 °C.
The bond strength of NR linings on steel is excellent. The hardness is typically Shore A 55 for soft rubber and Shore D 75 for hard natural rubber.
2. Synthetic isoprene rubber (IR)
Isoprene rubber is a synthetic alternative form of NR, and has similar properties.
3. Styrene-butadiene rubber (SBR)
Styrene-butadiene rubber can be used for the containment of automotive brake fluids, alcohols and mixtures of alcohol and water. The allowable service temperature range is -30 °C to +80 °C. The hardness is in the same range as that of soft natural rubber (NR).
4. Chloroprene rubber (CR)
Chloroprene rubber is resistant to ozone and sunlight, and reasonably resistant to oils and chlorine. Special compounds are suitable for use with refrigerants (e.g. Freon 12 and 22).
The allowable service temperature range is -30 °C to +105 °C. Hardness is approximately Shore A 60.
5. Butyl rubbers (IIR, BIIR, CIIR)
Butyl rubbers have excellent tolerance to hydrochloric acid. Butyl rubber is resistant to ozone and sunlight, non-flammable hydraulic fluids, animal and vegetable oils, water, alcohols, ketones and acids. Butyl rubber should not be used in the presence of free halogens, petroleum oils or halogenated or aromatic hydrocarbons. The allowable service temperature range is -30 °C to +110 °C. Hardness is in the range of Shore A 55 to A 60.
6. Nitrile butadiene rubber (NBR)
Nitrile butadiene rubber (also known as BuNa-N) is a copolymer of butadiene and acrylonitrile. The acrylonitrile content must be at least 35% by mole to obtain good chemical resistance. Nitrile rubbers are resistant to petroleum-based hydraulic and lubricating oils, animal and vegetable oils, acetylene, alcohols, water, alkalis and fuel oils. Nitrile rubber should not be used for phenols, ketones, acetic acids, most aromatic hydrocarbons and nitrogen derivatives. The allowable service temperature is -35 °C to +80 °C. Hardness is approximately Shore A 60.
7. Ethylene propylene rubbers (EPDM / EPM)
Ethylene propylene rubbers are resistant to ozone and sunlight, oxidizing chemicals, non-flammable hydraulic fluids, pure aniline, fire extinguisher liquids, acids, hot water and steam. However, these rubbers are not resistant to mineral oils, petrol solvents and aromatic hydrocarbons. The allowable service temperature range is -40 °C to +150 °C. Hardness is typically in the range Shore A 40 to A 80.
8. Urethane rubber (UR)
Urethane rubber has excellent wear/erosion resistance and is chemically resistant to mineral oils, fuels and ozone. Urethane rubber should not be used for concentrated acids, ketones or chlorinated hydrocarbons, and shall not be used for water above 50 °C.
Otherwise, the allowable service temperature range is -40 °C to +70 °C. Hardness is typically in the range Shore A 50 to A 80.
9. Chlorosulphonated polyethylene (CSM)
Chlorosulphonated polyethylene is a highly wear-resistant synthetic rubber with excellent resistance to heat, ozone sunlight, oxidising media, sodium hypochlorite and sulphuric acid.
CSM rubber has also good resistance to most oils, lubricants and aliphatic hydrocarbons, but is unsuitable for use with esters and ketones. The allowable service temperature range is -35 °C to +80 °C. Hardness is approximately Shore A 60.
 
10. Fluoro-elastomers (FKM)
Fluoro-elastomers are copolymers of hexa-fluoro-propylene and vinyldiene fluoride. They are suitable for both high-temperature and vacuum applications. These materials have excellent resistance to oils, fuels, lubricants, carbon tetrachloride, most concentrated acids and many aliphatic and aromatic hydrocarbons such as toluenes, benzene and xylene.
They should not, however, be used with low molecular weight esters and ethers, ketones, certain amines and hot anhydrous hydrofluoric or chlorosulphonic acids. These materials are also resistant to ozone and sunlight and can be used in contact with many corrosive gases, e.g. bromine and chlorine. However, they are not resistant to ammonia or highpressure steam. The allowable service temperature range is -20 °C to +230 °C. Hardness is typically in the range Shore A 60 to A 90.

Payment Terms︰ T/T

Product Image